PL3000
12 DIGIT HEAVY DUTY PRINTING CALCULATOR
INSTRUCTION MANUAL
1. OPERATIONS AND MAINTENANCE
Printer Switch – This switch is located on upper portion of the keyboard. Slide the switch
depend on your application.
OFF
NP
P
-
-
-
Power OFF the Calculator.
Non-print mode, if only the display is needed.
Print mode, if you wish to have the printer to be operational.
CAUTIONS
-
The calculator must not be covered when turned on. This will cause the unit to
overheat.
-
-
Do not use organic solutions such as alcohol to clean the housing.
Do not use or leave the calculator in direct sun light. Areas subject to quick
temperature changes, high humidity and dirt should be avoided.
2. REPLACING INK CARTRIDGE
3
1. Remove printer cover.
2. Remove ink cartridge.
3. Insert new cartridge.
3. LOADING PAPER
1. Plug in calculator and turn it on.
2. Cut or tear evenly the end of paper rolls to get a straight, even edge for proper
feeding through the printer head.
3. While holding the paper roll in one hand, feed the paper from the bottom of the roll and
insert into the paper slot at the back of the calculator.
4. Depress paper feed key until the paper catches and advances through the printer.
5. Place the paper roll on the dual paper holders.
Correct method of removing the paper
PLEASE TAKE NOTE :
1.
Please DO NOT pull the paper in a reverse way once the paper is loaded
into the printer.
2.
Please DO NOT pull the paper out from the printer.
3. ALWAYS tear the paper with a Paper Cutter before removing the paper from the
printer.
4
4. DISPLAYED SYMBOLS
5. KEYBOARD LAYOUT
1
2
3
4
5
7
8
9
10
11
12
13
6
14
15
16
18
19
20
29
30
31
25
26
23
27
28
17
32
21
24
22
1. Print Switch
12. Tax 1
23. Subtraction
2. Rounding Selector
3. Decimal Selector
4. Loan Switch
5. Grand Total Switch
6. Paper Feed
13. Tax 2
24. Addition / OK
14. Back Space
15. Percentage
16. Grand Total
25. Time / Date Display
26. Item Count
27. Subtotal / Date
28. Total
17. Clear Entry / Clear
7. Delta Percentage
18. Division
29. Memory Total / Amount
5
8. Cost
19. Equal
30. Memory Subtotal / Interest
9. Sell
20. Multiplication
31. Memory Subtraction / Month
10. Margin
21. Sign Change
32. Memory Addition / Payment
11. Tax Rate Preset
22. Numeric Key Pad
6. SLIDER SWITCH FEATURES
1. OFF NP P Printer Selects Switch
OFF
Turn OFF the calculator.
NP (Non-print) Printer is activated only when feed key or non-add/date key is
pressed.
PRINT Printer is activated as long as calculator is turned on.
2. ↓ 5/4 ↑
Rounding Switch
↓
Absolute round down.
5/4
Final result is rounded up if the 1st digit not to be printed is 5 or more
and rounded down if the 1st digit not to be printed is 4 or less.
↑
Absolute round up.
3. A 0 2 3 4 F Decimal Point Selector
Add mode. The decimal point is automatically placed before the last two
digits in addition and subtraction.
A
0,2,3,4 For multiplication and division, decimal point is set to the result of
calculation. For addition and subtraction, decimal point is set to all
entries. To all the results, number in the decimal place to the last decimal
place designated will be rounded. For example, number at 3rd decimal
place is rounded at “2” position.
F
Automatic floating point for decimally accurate computing. Decimal
point is entered at desired position and the decimal point is
automatically shifted to the right is under 14 digits of integer.
4. Loan Switch
•
Memory calculation is on. Loan calculation is off. MT, MS, M-, and M+
keys are activated.
Loan Loan calculation is on. Memory calculation is off. Amount, Interest,
Month, and Payment keys are activated.
5. Grand Total Switch
•
Calculation without Grand Total
GT
Any total taken with the T key is automatically accumulated to Grand
Total. The accumulated grand total can be recalled by pressing the GT
key.
6
7. KEY FEATURES
6. [↑] Paper feed key
Advance the paper roll.
7. [Δ%] Delta Percentage
Automatically compares any two amounts and then calculates and prints the
percent change.
8. [COST] Cost key
Calculate amount exclude profit margin. Used to enter the cost when
determining the margin or sell price.
9. [SELL] Sell key
Calculate amount include profit margin. Used to enter the sell price when
determining the cost or margin.
10. [MARGIN] Profit margin
Used to enter profit margin. Used to enter the profit margin when determining
the cost or sell price.
11. [RATE] TAX rate preset key
Used to enter TAX rate.
12. [TAX1] Tax 1 key
Calculate an amount Value Added Tax (VAT) with tax rate preset by RATE key.
Use + key for calculating an amount including VAT, and – key for calculating an
amount excluding VAT.
13. [TAX2] Tax 2 key
Calculate an amount VAT with tax rate preset by RATE key. Use + key for
calculating an amount including VAT, and – key for calculating an amount
excluding VAT.
14. [→] Right shift key
Deletes right most character of a live entry
15. [%+] Percent key
Completes percent calculation when Multiple or Division key is used.
16. [GT] Grand Total key
Print and clear the Grand Total Accumulator.
17. [CE/C] Clear Entry / Clear key
7
Clears a live entry by pressing this key once. Press twice to clear the
accumulator or pending calculation. Does not clear the Memory or Grand total.
18. [÷] Division key
To divide, enter the number to be divided (dividend) then depress the Divide key.
Then enter the second number (divisor) and depress Equals or other keys as
necessary to obtain a result. If the key is depressed repeatedly, it will make
sequential division calculations.
19. [=] Equal key
To get the result in multiplication or division.
20. [X] Multiplication key
To multiply, enter the first number (multiplicand) and depress the Times key.
Then enter the second number (multiplier) and depress Equals or other keys as
necessary to obtain a result. If the key is depressed repeatedly, it will make
sequential multiple calculations.
21. [+/-] Sign change key
Reverse the sign on the display.
22. [0]-[9], [00] & [•] Numeric keys.
Any numeral over 12 digits will be ineffective. When decimal point key is used
more than once in one numeral, the first decimal point will be considered as
effective.
23. [−] Minus key
Subtracts an amount from the accumulator. To subtract the same amount more
than one time (repeat subtraction), enter that amount once and depress the
Minus key as many times as necessary. If this key is depressed immediately
after [%] key, it works as percent minus key.
24. [+] Plus key
Adds an amount to the accumulator. To add the same amount more than one
time (repeat addition), enter that amount once and depress the Plus key as
many times as necessary. If this key is depressed immediately after [%] key, it
works as percent plus key.
25. [TIME/DATE] Time and Date display key
Used to display or program the date and time. Depressing this key once will
cause the date to display, a second depression will display the time. Holding the
key down for three seconds will cause the date or time to flash, this is the
program mode.
26. [N] Item Count key
Calculations with item count.
27. [# / S] Date / Subtotal key
#: Prints the entered figure as an identifier or invoice number with the “#”
symbol.
S: Prints a Subtotal of the numbers in the accumulator without clearing the
accumulator. Used if the operator needs to see what’s in the accumulator, then
8
proceed without clearing the accumulator.
28. [T] Total key
Prints and clears the accumulator. When this key is pressed with the “GT” switch
on, the result is accumulated automatically in the grand total memory.
29. [MT / Amount] Memory Total key / Amount
If the Loan switch is off, MT is activated and if the Loan switch is on,
Amount is activated.
MT:
Prints and clears the memory.
Amount: If this key is pressed after a value is entered, it is entered as the Loan
Amount. However, if Interest, Month, and Payment are entered in
prior or modification is done on any of the three as above in prior,
user can calculate / recalculate the Loan Amount by press this key.
30. [MS / Interest] Memory Subtotal key / Interest
If the Loan switch is off, MS is activated and if the Loan switch is on,
Interest is activated.
MS: Prints but do not clear the memory.
Interest: If this key is pressed after a value is entered, it is entered as the Loan
Interest. However, if Amount, Month, and Payment are entered in
prior or modification is done on any of the three as above in prior,
user can calculate / recalculate the Loan Interest by press this key.
31. [M− / Month] Memory Minus key / Months
If the Loan switch is off, M- is activated and if the Loan switch is on, the
Month function is activated.
M−: Subtracts an amount from memory. If there is a live calculation pending, the
Memory Minus key will complete the calculation and subtract the amount
from Memory.
Month: If this key is pressed after a value is entered, it is entered as Number of
Months to settle the Loan. If Amount, Interest, and Payment are
entered in prior, or modification is done on any of the three as above
in prior, user can calculate / recalculate the Number of Months by
press this key.
32. [M+ / Payment] Memory Plus key / Payment
If the Loan switch is off, M+ is activated and if the Loan switch is on, the
Payment function is activated.
M+: Adds an amount to memory. If there is a live calculation pending, the
Memory plus key will complete the calculation and accumulate the result
to Memory.
Payment: If this key is pressed after a value is entered, it is entered as the
Payment. If Amount, Interest, and Months are entered in prior, or
modification is done on any of the three as above in prior, user can
calculate / recalculate the Payment by press this key.
9
8. CALCULATION EXAMPLES
1. ADDITION / SUBTRACTION
Print
Rounding
Decimal
Loan
GT
P
5/4
F
.
.
Calculation
Enter
2 [+]
Display
Paper
2 + 3.1415926 - 6 = ?
2.
2. +
2. +
2.
3.1415926
[+]
3.1415926 +
3.1415926
5.14145926 +
3.1415926
6.
-0.8584074 -
6 [−]
6. −
[T]
− 0.8584074 ∗
− 0.8584074
2. ADDITION / SUBTRACTION IN ADD MODE
Print
Rounding
Decimal
Loan
GT
P
5/4
A
.
.
10
Calculation
Enter
123 [+]
Display
Paper
1.23 − 4.56 + 7.89 = ?
1.23
1.23 +
1.23 +
456 [−]
1.23
4.56
4.56 −
-3.33 -
1.23
4.56
-3.33
[#/S]
- 3.33 ◊
4.56
7.89
4.56 +
7.89 +
789 [+]
[T]
4.56 ∗
4.56
3. ITEM COUNT PRESETTING
Print
Rounding
Decimal
Loan
GT
P
5/4
A
.
.
Calculation
Enter
[CE/C]
Display
Paper
0.
Setting
Item Count Plus
0. C
IC+
[N]
(Blinking)
000………………
Count Plus
(Press & Hold 3 sec)
0.
IC+
[+]
0.
[CE/C]
IC+
0.
Setting Item
Count Plus/Minus
[N]
0. C
000………………
IC+
(Blinking)
(Press & Hold 3 sec)
0.
[-]
(Blinking) IC±
0.
11
4. ADDITION / SUBTRACTION WITH ITEM COUNT
Print
Rounding
Decimal
Loan
GT
P
5/4
A
.
.
Calculation
Enter
Display
Paper
11.32 + 7.98 − 33.33 = ?
1132 [+]
11.32
11.32 +
11.32 +
7.98 +
11.32
7.98
19.30 +
798 [+]
[N]
IC+
002………………
2.
[#/S]
19.30 ◊
19.30
3333 [−]
33.33
33.33 –
-14.03 -
IC+
[N]
001………………
3.
-14.03
- 14.03 ∗
12
0. C
[T]
[CE/C]
0.
5. GRAND TOTAL MEMORY
Print
Rounding
Decimal
Loan
GT
P
5/4
A
.
GT
Calculation
Enter
Display
Paper
13.20 9.55
8.30 7.36
[CE/C]
0. C
0.
+ 2.95 18.33
24.45 +35.24 =T?
13.20
13.20 +
13.2 [+]
8.3 [+]
13.20 +
8.30 +
13.20
8.30
21.50 +
8.30
2.95
[+]
2.95 +
24.45 +
GT
24.45
24.45
24.45 ∗+
9.55 +
[T]
GT
9.55
9.55 [+]
7.36 [+]
9.55 +
GT
9.55
7.36 +
7.36
16.91 +
13
18.33 +
GT
GT
7.36
18.33
35.24 +
18.33 [+]
[T]
59.69
35.24
[GT]
59.69
6. REPETATIVE CALCULATION WITH REFERENCE TO DATE
Print
Rounding
Decimal
Loan
GT
P
5/4
A
.
.
Calculation
Enter
Display
Paper
6.54 + 6.54 + 6.54 −
7.89 − 7.89 = ?
9.21.2007
[#/S]
# 9.21.2007……
9.212007
6.54 +
6.54
6.54 +
654 [+]
[+]
6.54
6.54
6.54 +
6.54 +
13.08 +
6.54
6.54
19.62 +
[+]
6.54
7.89
11.73 -
789 [−]
7.89 −
7.89 −
3.84 ∗
7.89
7.89
3.84 -
[−]
14
[T]
3.84
7. ROUNDING FOR ADDITION / SUBTRACTION
Print
Rounding
Decimal
Loan
GT
P
↓
0
.
.
Calculation
Enter
Display
Paper
3.4 + 2.1 = ?
3.4 +
3.4 [+]
3.4
3.4 +
3.4
2.1
5.5 +
2.1[+]
[T]
2.1 +
5. ∗
5.
Print
Rounding
Decimal
Loan
GT
P
5/4
0
.
.
Calculation
Enter
Display
Paper
3.4 + 2.1 = ?
3.4 +
3.4 [+]
3.4
3.4 +
3.4
2.1
5.5 +
2.1 +
6. ∗
2.1[+]
[T]
6.
8. RIGHT SHIFT
Print
Rounding
Decimal
Loan
GT
P
5/4
4
.
.
Calculation
Enter
Display
Paper
5.4321 + 2.34567 = ?
5.4321 [+]
5.4321 +
5.4321
5.4321 +
2.3457 [→]
5.4321
2.345 +
5.4321
2.34567
7.77777 +
2.34567 +
67 [+]
[T]
7.7778 ∗
7.7778
9. CONSTANT MULTIPLICATION
Print
Rounding
Decimal
Loan
GT
16
P
5/4
2
.
.
Calculation
2 × 4 = 8
2 × 5 = 10
2 × 6 = 12
Enter
Display
Paper
2.00 ×
2 [×]
2.00 X
4.00 =
4 [=]
5 [=]
6 [=]
8.00 ∗
8.00 =
5.00 =
10.00 ∗
10.00 =
12.00 =
6.00 =
12.00 ∗
10. CONSTANT DIVISION
Print
Rounding
Decimal
Loan
GT
P
5/4
2
.
.
Calculation
Enter
Display
Paper
755 ÷ 4 = 188.75
409 ÷ 4 = 102.25
32 ÷ 4 = 8.00
755.00 ÷
755 [÷]
755.00 ÷
4.00 =
4 [=]
188.75 ∗
188.75 =
102.25 =
8.00 =
409.00 =
409 [=]
32 [=]
102.25 ∗
32.00 =
8.00 ∗
11. DISCOUNT CALCULATION
Print
Rounding
Decimal
Loan
GT
P
5/4
2
.
.
Calculation
Enter
Display
Paper
17
Price = $169.50
Discount = 14%
Discount price = $23.73
Net = $145.77
169.50 ×
169.5 [×]
169.50 x
169.501
14.00 %
23.73 =
14 [%+]
14.00 %
23.73 ∗
[-]
145.77 -%
145.77 %-
12. DELTA PERCENTAGE CALCULATION
Print
Rounding
Decimal
Loan
GT
P
5/4
2
.
.
Calculation
Enter
Display
Paper
175,000−125,000
= 50,000
125’000.00
125’000.00
125,000.00 Δ
175,000.00 =
50,000.00 Δ∗
40.00 Δ%
125000 [Δ%]
50,000 ÷ 125,000
x 100 = 40%
125’000.00
175’000.00 Δ
125’000.00 Δ% =
175000 [=]
13. PROFIT MARGIN
Print
Rounding
Decimal
Loan
GT
P
5/4
2
.
.
Calculation
Cost = 100
Margin = 5%
Sell = ?
Enter
Display
100.00
100.00
Paper
COST
100.00 C
5.00 M%
5.26 Δ∗
100 [COST]
105.26 ◊
COST
SELL
100.00
5.00 %
105.26 =
5 [MARGIN]
18
SELL
150.00
150.00
150.00 ◊
10.00 M%
15.00 Δ∗
135.00 C
Sell = 150.00
Margin = 10%
Cost = ?
150 [SELL]
0
10 [MARGIN]
SELL
150.00
10.00 %
135.00 =
COST
14. MEMORY CALCULATION
Print
Rounding
Decimal
Loan
GT
P
5/4
F
.
.
Calculation
Enter
Display
Paper
0. C
100 + 200 = 300
100 [+]
100.
100. +
100. +
90 - 50
20 X 7
= 40
= 140
300-40+140 =?
100.
200.
300. +
200. +
200 [+]
[T]
300. ∗
300.
[M+]
M
300.
300.
300. M+
90.+
90 [+]
50 [-]
M
M
90.
90. +
90.
50.
50.-
40. -
40.∗
M
300.
40.
19
40. M-
[T]
M
M
260.
40.
[M-]
20 [X]
260.
20. x
7 [M+]
M
M
400.
140.
400
400.
[MS]
[MT]
400.
15. TAX RATE PRESETTING
Print
Rounding
Decimal
Loan
GT
P
5/4
2
.
.
Calculation
Enter
Display
Paper
0. C
Preset
[CE/C]
TAX1 = 7.5%
0.
(Blink) RATE
[RATE]
(Press & Hold 3 sec)
0.
………1………
7.5 %
RATE
TAX1
7.5 [TAX1]
7.5 %
(Blink) RATE
Preset
[RATE]
TAX2 = 18.6%
(Press & hold for 3 sec)
0.
……….2………
18.6 %
RATE
TAX2
18.6 [TAX2]
18.6 %
20
16. TAX CALCULATION
Print
Rounding
Decimal
Loan
GT
P
↑
2
.
.
Calculation
Enter
Display
Paper
[CE/C]
0. C
261.56
………1………
7.5 %
Price = 261.56
0.
261.56
19.62 Δ
281.18
19.62 Δ
281.18 ∗
Price with Tax 1 = ?
Price without Tax 1=?
261.56
TAX1+
[TAX1] [+]
=
281.18
281.18
19.62 Δ
261.56
………1………
[TAX1] [-]
TAX1-
7.5 %
19.62 Δ
261.56 ∗
=
0. C
[CE/C]
300.00
0.
………2………
18.6 %
55.80 Δ
355.80 ∗
300.00
55.80 Δ
355.80
Price = 300
300
TAX2+
=
Price with Tax 2 = ?
[TAX 2][+]
355.80
355.80
55.80 Δ
300.00
……..2………
18.6 %
55.80 Δ
300.00 ∗
21
Price without Tax 2=?
[TAX 2] [-]
TAX2-
=
VAT including
200.00
52.20 Δ TAX1+
TAX 1 and TAX 2:
200
200.00
…….…1………
[TAX 1]
[TAX 2] [+]
252.20
TAX2+
=
7.5 %
15.00 Δ
………2………
18.6 %
37.20 Δ
…….1,2……
52.20 Δ
252.20 ∗
17. DATE AND TIME DISPLAY PRESETTING
Print
Rounding
Decimal
Loan
GT
P
5/4
F
.
.
Setting
Enter
[CE/C]
Display
Paper
Set Date
0. C
August 14, 2007
[TIME/DATE]
(Press & Hold 3 sec)
(Blink)MM-DD-YYYY
08-14-2007
# .8.14.2007……
08142007
[TIME/DATE]
[# / S]
Set Time to
4:37 PM
[TIME/DATE]
08-14-2007
TIME/DATE]
(Press & Hold 3 sec)
(Blink)HH - MM
P 04-37
1637
[TIME/DATE]
# .04.37…………
22
[# / S]
18. LOAN CALCULATION
Note : The « FIN » symbol is displayed when Loan Calculation is ON.
Print
P
Rounding Decimal Loan
5/4 Loan
GT
.
2
Example : Assume you are interested in purchasing a house for 100,000.
The interest rate is 6.5%. You want to finance the loan over a period of 180 months.
Calculate for payment per month.
Payment Calculation
Calculation
Enter
Display
Paper
FIN
Amount = 100,000
Interest = 6.5%
Period = 180 months
Payment =?
[CE/C]
0. C
0.
FIN MTH 0.
(Blink)
0. % INT
0. AMT
[Payment]
---------------- PAY
FIN MTH 180.
0. % INT (Blink)
0. AMT
[180] [+ Ok]
[6.5] [+ Ok]
---------------- PAY
180.M
FIN MTH 180.
6.50 % INT
0. AMT (Blink)
---------------- PAY
6.50 %
23
100,000.00Δ
871.11∗C
FIN MTH 180.
6.50 % INT
100’000.00 AMT
871.11 PAY =
[100000] [+ OK]
Note: To re-solve the loan amount for a different payment, interest, or months, press the
amount key and follow the prompts. Press OK to accept existing figures or enter new
figure, and press OK.
Interest Calculation
Calculation
Enter
Display
Paper
Amount = 100,000
[CE/C]
FIN
0. C
Period = 180 months
Payment = 871.11
Interest = ?
0.
FIN MTH 0. ------------- % INT
[Interest]
(Blink)
0. AMT
0. PAY
180. M
FIN MTH 180.
0. % INT
0. AMT (Blink)
0. PAY
[180] [+ OK]
100,000.00 Δ
FIN MTH 180.
0. % INT
100’000.00 AMT
0. PAY (Blink)
[100000] [+ OK]
[871.11] [+ OK]
871.11 c
6.50 ∗%
FIN MTH 180. 6.50 % INT
100’000.00 AMT
871.11 PAY =
24
Month Calculation
Calculation
Enter
Display
Paper
FIN
Amount = 100,000
Payment = 871.11
Interest = 6.5%
[CE/C]
0. C
0.
FIN MTH ---
FIN MTH ---
FIN MTH ---
0. % INT (Blink)
0. AMT
0. PAY
Period = ?
[Month]
6.50%
6.5 % INT
0. AMT (Blink)
0. PAY
[6.5] [+ OK]
100,000.00 Δ
6.5 % INT
100’000.00 AMT
0. PAY (Blink)
[100000] [+ OK]
[871.11] [+ OK]
871.11 c
180. ∗ M
FIN MTH 180
6.5 % INT
100’000.00 AMT
871.11. PAY =
Amount Calculation
Calculation
Enter
Display
Paper
Payment = 871.11
Interest = 6.5%
Period = 180 month
Amount = ?
0.C
FIN
[CE/C]
0.
FIN MTH
0.
0. % INT
--------------- AMT
0. PAY
[Amount]
(Blink)
180. M
FIN MTH 180
0. % INT (Blink)
0. AMT
[180] [+ OK]
0. PAY
FIN MTH 180
6.50 % INT
6.50 %
------------- AMT
0. PAY (Blink)
[6.5] [+ OK]
871.11 C
FIN MTH 180
6.50 % INT
100,000.30 ∗Δ
[871.11 [+ OK]
100’000.30 AMT
871.11. PAY =
25
9. TECHNICAL SPECIFICATIONS
Type:
Basic Operations:
Capacity:
Desktop Adding Machine/Calculator, Electronic Print/ LCD
Addition/subtraction and multiplication/division
Input and result 12 digits
Decimal System:
Functions:
Add mode(A), Floating(F), Fixed(0,2,3,4)
4 rules, successive calculation, memory calculation, grand
total memory, constant calculation, tax calculation, cost, sell,
margin calculation, and loan calculation.
Printer:
Ink Cartridge:
Paper width:
Display:
Character wheel selection type.
Two-color ink roller IR40T
Width 57.5 ± 0.5mm X Diameter 30mm
12 digit LCD display
Operating Temp:
Dimensions:
0°C ~ 40°C
198mm (W) x 250mm (D) x 57mm (H)
26
Weight:
895 gram
27
|